You are currently on the South East Asia (English) Armstrong Flooring site. For product availability and information for your current location, you may prefer browsing our Australia / New Zealand site.
Actualmente se encuentra en el sitio web de Armstrong Flooring de South East Asia (English). Para conocer la disponibilidad de productos e información sobre su ubicación actual, puede preferir navegar en nuestro sitio de America latina.
Vous vous trouvez actuellement sur le site South East Asia (English) d'Armstrong Flooring. Si vous désirez connaître la disponibilité des produits et obtenir des renseignements en fonction de votre emplacement, il serait préférable que vous consultiez notre site Canada.
The term ”low maintenance” is applied to a floor covering with a factory applied finish designed to reduce the amount of regular maintenance. The factory applied finish replaces the need to apply initial seal coats and finish (polish) coats, r educing the cost in both floor care products and labour. The floor covering will require maintenance in the form of cleaning and buffing with machinery, however the surface of a “low mainte nance” floor covering allows this process to be carried out quickly and cheaply.
What causes floor polish to powder off the flooring surface?
Powdering is the partial or total disintegration of the polish film resulting in a fine, light-colored material. Possible causes are floor not thoroughl y rinsed after stripping; dirty mops used to apply polish; surface of polish force-dried; ina dequate grit and soil control (no walk-off mats); mismatched polish and machine speed; floor pad t oo abrasive; room temperature too hot or too cold or humidity too high or too low or excessiv e alkaline moisture permeating through tile from subfloor. To correct the problem, follow stripping recommendations for the specific flooring.
What causes streaks in floor polish?
Possible causes of streaks can be too much or too little floor polish applied in one coat; dirty mop used to apply polish; inadequate drying time or alkaline residue on the floor. Follow recommendations for stripping or heavy cleaning, and then follow recommended procedure for preparation for commercial traffic.
What can cause bleeding of brightly colored vinyl composition tile?
Possible causes are too little floor polish; clea ning/stripping solutions too aggressive or colored pigments removed by abrasion from coarse stripping or scrubbing pads. Following the recommended maintenance procedures will prevent the problem.
How long after an installation should a floor be protected from rolling loads?
Newly installed commercial flooring should not be exposed to routine rolling load traffic (carts, trolley jacks, etc.) for at least 72 hours after in stallation to allow setting and drying of adhesives. If rolling loads cannot be avoided, protect the installa tion for 72 hours after installation by covering with wood panels.
Furniture is sticking to the floor. What can cause this to happen?
Furniture sticking is normally caused by the fo llowing conditions: Furniture replaced too soon after polishing; furniture left in place while polish was applied; floor not properly rinsed; sealer/polish not compatible; polish not properly cured/dried (floor temperature too low, high humidity, recoated too quickly, building closed up with no air circulation, dew point too high, contaminated mops or finishes); slow drying polish formulations; furniture rests have something on them (not clean); excess moisture from damp mopping. Some possible solutions include: Only apply polish when drying conditions are right; use brand-name products; clean furniture rests as needed; test for dryness. Tip - to release struck furniture, tap the legs near to the floor, hitting firmly in a horizontal direction. Be sure to prot ect legs to avoid scratching or marring. Do not attempt to lift furniture straight up before loosening.
What is antioxidant staining in vinyl floors?
Armstrong's vinyl floors have been formulated to be very stain resistant to most reagents and traffic. Certain compounds added to rubber can di scolor a vinyl floor when in contact with it. These chemical compounds, referred to as antiox idants, are formulated into rubber materials to extend the life of the rubber and prevent brittl eness. Some antioxidants react chemically with ingredients (plasticizers) in flexible vinyl to produ ce a yellowish stain. This is referred to in the vinyl industry as "antioxidant staining." Any sour ce of rubber containing these antioxidants in contact with the floor could produce this staini ng. Certain types of rubber mats, rubber-backed rugs, and rubber wheels on carts, can cause this di scoloration. To avoid this problem, insure that the mats and wheels which will be in contact with the vinyl floor are of the "non-staining" type of rubber.